If all you have to lift a light pole with is a chain, triple-wrap the chain around the pole as high as you can reach. Hold the pole while your lifting machine raises slowly, and allow it to pull the chain up the pole to where it will catch on the fixture flare. Only then should you release the pole.

How do you remove an old light pole?

If all you have to lift a light pole with is a chain, triple-wrap the chain around the pole as high as you can reach. Hold the pole while your lifting machine raises slowly, and allow it to pull the chain up the pole to where it will catch on the fixture flare. Only then should you release the pole.

How do you change a lightbulb you can't reach?

You can change a light bulb that you can’t reach with the use of a telescoping reacher grabber, which acts like an extension to your arm and has a trigger or squeeze handle that will operate the suction cups or jaws on the other end of the tool. Reacher grabbers are available at home improvement centers.

How do you change a lamp post light?

  1. Cut the Power. Identify which circuit breaker on your electrical panel controls your outdoor lamp post and turn it off. …
  2. Remove Old Post Lamp. Remove the old lamp from the post. …
  3. Connect New Lamp Wires. Follow directions on the new post lamp to ensure your fixture is connected properly. …
  4. Attach New Lamp.

How do you change a light fixture?

  1. Turn off power to the old fixture. …
  2. Remove the canopy to expose the wiring and fixture hardware. …
  3. Unscrew the three wires: black, white, and copper. …
  4. Remove old light fixture. …
  5. Install new bracket (sometimes). …
  6. Connect new fixture wires. …
  7. Secure the new fixture and adjust length (if there’s a chain).

How do you remove plastic light covers?

The sides of the lens sit on a ledge with a small lip, and you can push it out of place easily. To remove a wraparound fluorescent light cover, simply grab one long side, push up, and then pull it down. Do the same with the other side.

How do you remove an outdoor light cover without screws?

  1. Locate the finial (the fancy decorative bit in the middle of the dome).
  2. Turn the finial anticlockwise to loosen it. Keep one hand on the dome. …
  3. Completely unscrew the finial and the dome should come away in your hand.

How do you rewire an outdoor light?

  1. Step 1: Remove Existing Light. Before you begin any project dealing with electricity, you MUST disconnect the power at your main circuit breaker panel or fuse box. …
  2. Step 2: Replace the Mounting Bracket. A new light fixture should come with mounting hardware. …
  3. Step 3: Wire the Outdoor Light. …
  4. Step 4: Install the New Fixture.

How do I permanently remove a light fixture?

  1. Turn off the power to the fixture at the fuse box. …
  2. Snip the wires with wire cutters, freeing the fixture completely and leaving the wires hanging out of the box.
  3. Strip off about ¼ inch of insulation from the end of each of the wires, using your wire cutters.
How do you remove a square ceiling light cover?

Use a screwdriver to take out screws holding covers attached to the ceiling. Some covers swing downward on a hinge or hinges, which hold the cover while you change out the bulb underneath. Other cover styles remove completely from the fixture.

Article first time published on

How do I remove a light bulb?

  1. Replace the bulb. Insert a replacement bulb lightly but firmly into the socket. …
  2. Restore power. …
  3. Dispose of the old bulb.

How do you remove a glass shade from a pendant light?

1. Hold onto the glass, carefully reach inside your pendant from below and unscrew the lightbulb from the threaded socket. Next, unscrew the shade ring to fully release the glass from the socket and cord.

How do you remove a glass shade from a light fixture?

Hold the glass shade securely up while turning the metal nub or finial counterclockwise to remove it, like a screw. Some models may require a screwdriver. Catch the metal parts in your hand; there may be a washer as well. Gently pull the glass shade downward off the metal post holding it in place.

How do you remove a broken lightbulb from a high ceiling?

Hold a paper bag beneath the broken bulb and tap lightly to catch as many loose glass shards as possible. Use needle-nose pliers to grasp the metal base edge of the broken bulb and turn counterclockwise until the bulb is free.

How much does it cost to replace lighting fixtures?

How much does light fixture replacement cost? Light fixture replacement averages $65-$175 for labor. This will depend on the location of your light fixture and the type of replacement. The cost for the fixture itself can run anywhere from $20 for a simple option to $1,500 or more for a chandelier.